IEEE488.2 common commands | Measurement Function Setup
Load On/Off and Input Terminal Setup | Electronic Load Setup | Waveform Data Setup
Measurement Operation and Trigger Function | System Configuration | Register
|
|||
| *CLS | Clears the status data structures. | ||
| *ESE | Sets the event status enable register bits. | ||
| *ESR | Queries the event status register. | ||
| *IDN | Queries the identification string (manufacturer information). | ||
| *OPC | Causes the device to generate the operation complete message in the event status register when all pending selected device operations have been finished. | ||
| *RCL | Recalls the contents saved to the memory. | ||
| *RST | Performs a device reset. Configures the KFM2150 to a known condition independent from the usage history of the device. | ||
| *SAV | Saves the current settings to the memory. | ||
| *SRE | Sets the service request enable register bits. | ||
| *STB | Reads the status byte and master summary status bits. | ||
| *TRG | Trigger command | ||
| *TST | Since there is no self-test function built into the KFM2150. | ||
| *WAI | Prevents the device from executing subsequent commands or queries until the No Operation Pending flag becomes true. | ||
|
|||
| Impedance measurement (AC impedance method) | |||
| IMP:CURR:AC | Averaging period of the measured value | ||
| IMP:CURR:AC:RAT | Measuring AC current (percentage) | ||
| IMP:CURR:AC FREQ | Measuring frequency | ||
| Impedance measurement (current interrupt method) | |||
| IMP:CURR:PULS:TRAN | Pulse transition time | ||
| IMP:CURR:PULS:WIDT | Pulse width | ||
| IMP:CURR:PULS:DEPT:RAT | Pulse depth | ||
| IMP:CURR:PULS:DEPT | Pulse depth (current) | ||
| IMP:SAMP:POS | Sampling start position | ||
| IMP:SAMP:REG | Sampling region | ||
| Impedance measurement (averaging) | |||
| IMP:AVER:MOV:COUN | Moving average count | ||
| IMP:AVER:MOV:CLE | Moving average area | ||
| Measurement method | |||
| METH | Measurement method | ||
| Voltage measurement | |||
| VOLT:PROT:LOW | Voltage sensing undervoltage protection | ||
| VOLT:PROT:LOW:DEL | Voltage sensing undervoltage protection delay time | ||
|
|||
| Load on/off | |||
| INP | Load on/off | ||
| INP:PROT:CLE | Alarm clear | ||
| Soft start | |||
| INP:SST:RISE | Soft start falling edge | ||
| INP:SST:FALL | Soft start rising edge | ||
| INP:SST:RTIM | Remaining time | ||
| VOLTAGE SENSING terminal | |||
| INP:SENS:VOLT | VOLTAGE SENSING channel | ||
| CURRENT SENSING terminal | |||
| INP:SENS:CURR | CURRENT SENSING channel | ||
|
|||
| SOUR:CURR | AC current limit | ||
| SOUR:CURR:EXT | External electronic load DC current | ||
| SOUR:CURR:RANG | Electronic load DC current range | ||
| SOUR:VOLT | Voltage of PLZ-4W Series | ||
| SOUR:VOLT:RANG | Voltage range of PLZ-4W Series | ||
| SOUR:VOLT:PROT:LOW | Undervoltage protection | ||
| SOUR:POW:PROT | PLZ-4W OPP activation voltage of the electronic load DC voltage | ||
|
|||
| FORM:BORD | Data transmission/recording mode | ||
| FORM:PAGE:STAR | Length of the data to be transferred | ||
| FORM:PAGE:LENG | Start point of the data to be transferred | ||
| TRAC | Voltage waveform data or current waveform data | ||
|
|||
| Trigger function | |||
| TRIG:COUN | Sequence 1: Trigger count | ||
| TRIG:SEQ2:COUN | Sequence 2: Trigger count | ||
| TRIG:TIM | Sequence 1: Trigger time setting | ||
| TRIG:SEQ2:TIM | Sequence 2: Trigger time setting | ||
| TRIG:SOUR | Sequence 1: Trigger source | ||
| TRIG:SEQ2:SOUR | Sequence 2: Trigger source | ||
| INIT | Sequence 1 and 2: Start the trigger function | ||
| INIT:SEQ | Sequence 1: Start the trigger function | ||
| INIT:SEQ2 | Sequence 2: Start the trigger function | ||
| INIT:SEQ:WAV | Sequence 1: Starts the trigger function while holding the voltage and current waveform data | ||
| ABOR | Aborts the sequence 1 and 2 operations | ||
| *TRG or IEEE488.1 get (Group Execute Trigger) |
Software trigger | ||
| *RCL / *RST | Recall or Reset | ||
| Measurement operation | |||
| FETC / FETC:ARR | Queries the measured data | ||
| READ / READ:ARR | Starts the measurement and queries the data | ||
| MEAS:<meter_fn> / MEAS:ARR:<meter_fn> |
Resets a portion of the settings to default, start the measurement, and queries the data | ||
|
|||
| SYST:COMM:SER:PACE | Flow control condition | ||
| SYST:ERR | Reads the error information | ||
| SYST:LOC (RS232C and USB only) |
Sets to local | ||
| SYST:REM (RS232C and USB only) |
Sets the KFM2150 control to remote. Locks panels keys except the local key |
||
| SYST:RWL (RS232C and USB only) |
Sets the KFM2150 control to remote. Locks the panel operation. |
||
| SYST:VERS | Version of the SCPI specifications to which the KFM2150 conforms | ||
|
|||
| Status byte register | |||
| Event status register | |||
| OPERation status register | |||
| STAT:OPER | Queries the event | ||
| STAT:OPER:COND | Queries the condition of the register | ||
| STAT:OPER:ENAB | Enable register | ||
| STAT:OPER:NTR | Negative transition | ||
| STAT:OPER:PTR | Positive transition | ||
| OPERation:MEASuring status register | |||
| STAT:OPER:MEAS | Queries the event | ||
| STAT:OPER:MEAS:COND | Queries the condition of the register | ||
| STAT:OPER:MEAS:ENAB | Enable register | ||
| STAT:OPER:MEAS:NTR | Negative transition | ||
| STAT:OPER:MEAS:PTR | Positive transition | ||
| OPERation:TRIGger status register | |||
| STAT:OPER:TRIG | Queries the event | ||
| STAT:OPER:TRIG:COND | Queries the condition of the register | ||
| STAT:OPER:TRIG:ENAB | Enable register | ||
| STAT:OPER:TRIG:NTR | Negative transition | ||
| STAT:OPER:TRIG:PTR | Positive transition | ||
| OPERation:PROTecting status register | |||
| STAT:OPER:PROT | Queries the event | ||
| STAT:OPER:PROT:COND | Queries the condition of the register | ||
| STAT:OPER:PROT:ENAB | Enable register | ||
| STAT:OPER:PROT:NTR | Negative transition | ||
| STAT:OPER:PROT:PTR | Positive transition | ||
| QUEStionable status register | |||
| STAT:QUES | Queries the event | ||
| STAT:QUES:COND | Queries the condition of the register | ||
| STAT:QUES:ENAB | Enable register | ||
| STAT:QUES:NTR | Negative transition | ||
| STAT:QUES:PTR | Positive transition | ||
| Preset Status | |||
| STAT:PRES | Constructing status data | ||